Unaddressed Uncertainties When Scaling Regional Aircraft Emission Surveys to Basin Emission Estimates.

Wide-area aerial methods provide comprehensive screening of methane emissions from oil and gas (O & G) facilities in production basins. Emission detections ("plumes") from these studies are also frequently scaled to the basin level, but little is known regarding the uncertainties during scaling. This study analyzed an aircraft field study in the Denver-Julesburg basin to quantify how often plumes identified maintenance events, using a geospatial inventory of 12,629 O & G facilities. Study partners (7 midstream and production operators) provided the timing and location of 5910 maintenance events during the 6 week study period. Results indicated three substantial uncertainties with potential bias that were unaddressed in prior studies. First, plumes often detect maintenance events, which are large, short-duration, and poorly estimated by aircraft methods: 9.2 to 46% (38 to 52%) of plumes on production were likely known maintenance events. Second, plumes on midstream facilities were both infrequent and unpredictable, calling into question whether these estimates were representative of midstream emissions. Finally, 4 plumes attributed to O & G (19% of emissions detected by aircraft) were not aligned with any O & G location, indicating that the emissions had drifted downwind of some source. It is unclear how accurately aircraft methods estimate this type of plume; in this study, it had material impact on emission estimates. While aircraft surveys remain a powerful tool for identifying methane emissions on O & G facilities, this study indicates that additional data inputs, e.g., detailed GIS data, a more nuanced analysis of emission persistence and frequency, and improved sampling strategies are required to accurately scale plume estimates to basin emissions.

Simultaneous electrocoagulation and E-peroxone coupled with ultrafiltration membrane for shale gas produced water treatment.

Membrane fouling caused by the organics-coated particles was the main obstacle for the highly efficient shale gas produced water (SGPW) treatment and recycling. In this study, a novel hybrid electrocoagulation (EC) and E-peroxone process coupled with UF (ECP-UF) process was proposed to examine the efficacy and elucidate the mechanism for UF fouling mitigation in assisting SGPW reuse. Compared to the TMP (transmembrane pressure) increase of -15 kPa in the EC-UF process, TMP in ECP-UF system marginally increased to -1.4 kPa for 3 filtration cycles under the current density of 15 mA/cm2. Both the total fouling index and hydraulically irreversible fouling index of the ECP-UF process were significantly lower than those of EC-UF process. According to the extended Derjaguin-Landau-Verwey-Overbeek theory, the potential barriers was the highest for ECP-UF processes due to the substantial increase of the acid-base interaction energy in ECP-UF process, which was well consistent with the TMP and SEM results. Turbidity and TOC of ECP-UF process were 63.6% and 45.8% lower than those of EC-UF process, respectively. According to the MW distribution, the variations of compounds and their relative contents were probably due to the oxidation and decomposing products of the macromolecular organics. The number of aromatic compound decreased, while the number of open-chain compounds (i.e., alkenes, alkanes and alcohols) increased in the permeate of ECP-UF process. Notably, the substantial decrease in the relative abundance of di-phthalate compounds was attributed to the high reactivity of these compounds with ·OH. Mechanism study indicated that ECP could realize the simultaneous coagulation, H2O2 generation and activation by O3, facilitating the enhancement of ·OH and Alb production and therefore beneficial for the improved water quality and UF fouling mitigation. Therefore, the ECP-UF process emerges as a high-efficient and space-saving approach, yielding a synergistic effect in mitigating UF fouling for SGPW recycling.

Temporal Variation and Persistence of Methane Emissions from Shallow Water Oil and Gas Production in the Gulf of Mexico.

Methane emissions from the oil and gas supply chain can be intermittent, posing challenges for monitoring and mitigation efforts. This study examines shallow water facilities in the US Gulf of Mexico with repeat atmospheric observations to evaluate temporal variation in site-specific methane emissions. We combine new and previous observations to develop a longitudinal study, spanning from days to months to almost five years, evaluating the emissions behavior of sites over time. We also define and determine the chance of subsequent detection (CSD): the likelihood that an emitting site will be observed emitting again. The average emitting central hub in the Gulf has a 74% CSD at any time interval. Eight facilities contribute 50% of total emissions and are over 80% persistent with a 96% CSD above 100 kg/h and 46% persistent with a 42% CSD above 1000 kg/h, indicating that large emissions are persistent at certain sites. Forward-looking infrared (FLIR) footage shows many of these sites exhibiting cold venting. This suggests that for offshore, a low sampling frequency over large spatial coverage can capture typical site emissions behavior and identify targets for mitigation. We further demonstrate the preliminary use of space-based observations to monitor offshore emissions over time.

Two-stage thermal pyrolysis of plastic solid waste: Set-up and operative conditions investigation for gaseous fuel production.

In response to the escalating global challenge of mounting plastic waste and the imperative to adopt more sustainable practices for resource utilization, our study focuses on the utilization of plastic solid waste (PSW) through a two-stage thermal pyrolysis process. This aims to demonstrate its potential as a high-performance alternative to existing two-stage catalytic pyrolysis methods. The experimentation involved processing real scrap PSW material in a lab-scale batch set-up, emphasizing optimizing residence time in the cracking reactor to maximize gas yield and its lower heating value (LHV). The study underscores the advantages of the employed two-stage thermal pyrolysis apparatus through a comparative analysis with established set-up dedicated to maximizing gas yield. Once the operative conditions were explored, resulting pyrolysis products underwent detailed characterization to assess their suitability as a sustainable fuel source. The study also presents a practical application of the produced gaseous fuel, envisioning its combustion in an internal combustion engine (ICE), known for its flexibility regarding fuel properties. This application is demonstrated through a simulation conducted in Unisim Design©. The successful processing of real PSW material in the two-stage lab-scale experimental set-up showcased optimal gas yield achievements (>65 % w/w) with an LHV (∼41 MJ/kg), comparable to that of natural gas. This emphasizes the potential of these sustainable alternatives to replace fossil fuels, especially in the context of ICE applications. The integration of the pyrolysis plant with an ICE demonstrated promising prospects for generating electricity in the transportation sector and facilitating thermal power for heat integration in pyrolysis reactors.

New generation mixed matrix membrane for CO2 separation: Transition from binary to quaternary mixed matrix membrane.

Contemporary advances in material development associated with membrane gas separation refer to the cost-effective fabrication of high-performance, defect-free mixed matrix membranes (MMMs). For clean energy production, natural gas purification, and CO2 capture from flue gas systems, constituting a functional integration of polymer matrix and inorganic filler materials find huge applications. The broad domain of research and development of MMMs focused on the selection of appropriate materials, inexpensive membrane fabrication, and comparative study with other gas separation membranes for real-world applications. This study addressed a comprehensive review of the advanced MMMs wrapping various facets of membrane material selection; polymer and filler particle morphology and compatibility between the phases and the relevance of several fillers in the assembly of MMMs are analyzed. Further, the research on binary MMMs, their problems, and solutions to overcome these challenges have also been discussed. Finally, the future directions and scope of work on quaternary MMM are scrutinized in the article.

Modelling spatial & temporal variability of air pollution in an area of unconventional natural gas operations.

Despite the growing unconventional natural gas production industry in northeastern British Columbia, Canada, few studies have explored the air quality implications on human health in nearby communities. Researchers who have worked with pregnant women in this area have found higher levels of volatile organic compounds (VOCs) in the indoor air of their homes associated with higher density and closer proximity to gas wells. To inform ongoing exposure assessments, this study develops land use regression (LUR) models to predict ambient air pollution at the homes of pregnant women by using natural gas production activities as predictor variables. Using the existing monitoring network, the models were developed for three temporal scales for 12 air pollutants. The models predicting monthly, bi-annual, and annual mean concentrations explained 23%-94%, 54%-94%, and 73%-91% of the variability in air pollutant concentrations, respectively. These models can be used to investigate associations between prenatal exposure to air pollutants associated with natural gas production and adverse health outcomes in northeastern British Columbia.

Indoor Air Sources of Outdoor Air Pollution: Health Consequences, Policy, and Recommendations: An Official American Thoracic Society Workshop Report.

Indoor sources of air pollution worsen indoor and outdoor air quality. Thus, identifying and reducing indoor pollutant sources would decrease both indoor and outdoor air pollution, benefit public health, and help address the climate crisis. As outdoor sources come under regulatory control, unregulated indoor sources become a rising percentage of the problem. This American Thoracic Society workshop was convened in 2022 to evaluate this increasing proportion of indoor contributions to outdoor air quality. The workshop was conducted by physicians and scientists, including atmospheric and aerosol scientists, environmental engineers, toxicologists, epidemiologists, regulatory policy experts, and pediatric and adult pulmonologists. Presentations and discussion sessions were centered on 1) the generation and migration of pollutants from indoors to outdoors, 2) the sources and circumstances representing the greatest threat, and 3) effective remedies to reduce the health burden of indoor sources of air pollution. The scope of the workshop was residential and commercial sources of indoor air pollution in the United States. Topics included wood burning, natural gas, cooking, evaporative volatile organic compounds, source apportionment, and regulatory policy. The workshop concluded that indoor sources of air pollution are significant contributors to outdoor air quality and that source control and filtration are the most effective measures to reduce indoor contributions to outdoor air. Interventions should prioritize environmental justice: Households of lower socioeconomic status have higher concentrations of indoor air pollutants from both indoor and outdoor sources. We identify research priorities, potential health benefits, and mitigation actions to consider (e.g., switching from natural gas to electric stoves and transitioning to scent-free consumer products). The workshop committee emphasizes the benefits of combustion-free homes and businesses and recommends economic, legislative, and education strategies aimed at achieving this goal.

Climate Impacts of Hydrogen and Methane Emissions Can Considerably Reduce the Climate Benefits across Key Hydrogen Use Cases and Time Scales.

Recent investments in "clean" hydrogen as an alternative to fossil fuels are driven by anticipated climate benefits. However, most climate benefit calculations do not adequately account for all climate warming emissions and impacts over time. This study reanalyzes a previously published life cycle assessment as an illustrative example to show how the climate impacts of hydrogen deployment can be far greater than expected when including the warming effects of hydrogen emissions, observed methane emission intensities, and near-term time scales; this reduces the perceived climate benefits upon replacement of fossil fuel technologies. For example, for blue (natural gas with carbon capture) hydrogen pathways, the inclusion of upper-end hydrogen and methane emissions can yield an increase in warming in the near term by up to 50%, whereas lower-end emissions decrease warming impacts by at least 70%. For green (renewable-based electrolysis) hydrogen pathways, upper-end hydrogen emissions can reduce climate benefits in the near term by up to 25%. We also consider renewable electricity availability for green hydrogen and show that if it is not additional to what is needed to decarbonize the electric grid, there may be more warming than that seen with fossil fuel alternatives over all time scales. Assessments of hydrogen's climate impacts should include the aforementioned factors if hydrogen is to be an effective decarbonization tool.

Hydrochar and synthetic natural gas co-production for a full circular economy implementation via hydrothermal carbonization and methanation: An economic approach.

Herein we study the economic performance of hydrochar and synthetic natural gas co-production from olive tree pruning. The process entails a combination of hydrothermal carbonization and methanation. In a previous work, we evidenced that standalone hydrochar production via HTC results unprofitable. Hence, we propose a step forward on the process design by implementing a methanation, adding value to the gas effluent in an attempt to boost the overall process techno-economic aspects. Three different plant capacities were analyzed (312.5, 625 and 1250 kg/hr). The baseline scenarios showed that, under the current circumstances, our circular economy strategy in unprofitable. An analysis of the revenues shows that hydrochar selling price have a high impact on NPV and subsidies for renewable coal production could help to boost the profitability of the process. On the contrary, the analysis for natural gas prices reveals that prices 8 times higher than the current ones in Spain must be achieved to reach profitability. This seems unlikely even under the presence of a strong subsidy scheme. The costs analysis suggests that a remarkable electricity cost reduction or electricity consumption of the HTC stage could be a potential strategy to reach profitability scenarios. Furthermore, significant reduction of green hydrogen production costs is deemed instrumental to improve the economic performance of the process. These results show the formidable techno-economic challenge that our society faces in the path towards circular economy societies.

Quantifying flare combustion efficiency using an imaging Fourier transform spectrometer.

Mid-wavelength infrared (MWIR) imaging Fourier transform spectrometers (IFTSs) are a promising technology for measuring flare combustion efficiency (CE) and destruction removal efficiency (DRE). These devices generate spectrally resolved intensity images of the flare plume, which may then be used to infer column densities of relevant species along each pixel line-of-sight. In parallel, a 2D projected velocity field may be inferred from the apparent motion of flow features between successive images. Finally, the column densities and velocity field are combined to estimate the mass flow rates for the species needed to calculate the CE or DRE. Since the MWIR IFTS can measure key carbon-containing species in the flare plume, it is possible to measure CE without knowing the fuel flow rate, which is important for fenceline measurements. This work demonstrates this approach on a laboratory heated vent, and then deploys the technique on two working flares: a combustor burning natural gas at a known rate, and a steam-assisted flare at a petrochemical refinery. Analysis of the IFTS data highlights the potential of this approach, but also areas for future development to transform this approach into a reliable technique for quantifying flare emissions.Implications: Our research is motivated by the need to assess hydrocarbon emissions from flaring, which is a critical problem of global significance. For example, recent studies have shown that methane destruction efficiency of flaring from upstream oil may be significantly lower than the commonly assumed figure of 98%; work by Plant et al. , in particular, suggest that this discrepancy amounts to CO2 emissions from 2 to 8 million automobiles annually, considering the US alone. Similarly, the international energy agency (IEA) estimates a global flare efficiency of 92%, which translates in 8 million tons of CH4 emitted by flares in 2020. Highlighted by these studies and supported by the World Bank initiatives toward zero routine flaring emissions, there is an urgent need for oil and gas industry to assess their flare methane emission, and overall hydrocarbon emissions. At the very least, it is critical to identify problematic flare operating conditions and means to mitigate flare emissions. Focusing on remote quantification of plume species, the measurement technique and quantification method presented in this paper is a considerable step forward in that direction by computing combustion efficiency and key components for destruction efficiency.

Continuous biomethanation of flue gas-carbon dioxide using bio-integrated carbon capture and utilization.

Biomethanation of carbon dioxide (CO2) from flue gas is a potential enabler of the green transition, particularly when integrated with the power-to-gas chain. However, challenges arise in achieving synthetic natural gas quality when utilizing CO2 from diluted carbon sources, and the high costs of CO2 separation using amine-based solutions make large-scale implementation unfeasible. We propose an innovative continuous biomethanation system that integrates carbon capture and CO2 stripping through microbial utilization, eliminating expenses with the stripper. Stable continuous biomethane production (83-92 % methane purity) was achieved from flue gas-CO2 using a biocompatible aqueous n-methyldiethanolamine (MDEA) solution (50 mmol/L) under mesophilic and hydrogen-limiting conditions. MDEA was found to be recalcitrant to biodegradation and could be reused after regeneration. Demonstrating the microbial ability to simultaneously strip and convert the captured CO2 and regenerate MDEA provides a new pathway for valorization of flue gas CO2.

Human health risk assessment of volatile organic compounds in oil-based drill cuttings of shale gas.

Waste oil-based drill cuttings contain dioxins and volatile organic compounds (VOCs), which have the potential to cause serious health effects in humans. Therefore, this paper took oil-based drill cuttings (OBDCs) as the research object and carried out the testing of VOCs and dioxins content by using GC-MS and HRGCS-HRMS and comprehensively evaluated the content, composition and distribution pattern of VOCs and dioxins and the risk to human health posed by the two pollutants in OBDCs. The results showed that the VOCs did not exceed the emission limits in ESPPI (GB 31571-2015), but it is vital to recognise that 1,2-dichloropropane has the potential to cause cancer risk, with soil and groundwater risk control values of 662.95 mg·kg-1 and 0.066 mg·kg-1, respectively. Benzene, 1,2-dichloropropane and 8 other VOCs pose a non-carcinogenic risk to humans. The levels of polychlorinated dibenzofurans (PCDFs) exceeded those of polychlorinated dibenzo-p-dioxins (PCDDs), which accounted for 95.76 percent of the total PCDD/Fs, 2,3,4,7,8-P5CDF (56.00%), 2,3,7,8-T4CDF (9.20%), 1,2,3,6,7,8-H6CDF (8.80%) and 1,2,3,7,8-P5CDF (8.00%) were the main contributing monomers. The findings of the assessment on exposure risk indicate that there is a respiratory risk to oil-based drill cuttings dioxins for adults and children exceeded the World Health Organisation (WHO) acceptable daily intake (ADI) (1-4 pgTEQ/kg/d). Finally, three aspects of solid waste pre-treatment prior to incineration, the incineration process and post incineration were used to reduce the environmental and human health risks from dioxins.

Formaldehyde Exposure Racial Disparities in Southeast Texas.

Formaldehyde (HCHO) exposures during a full year were calculated for different race/ethnicity groups living in Southeast Texas using a chemical transport model tagged to track nine emission categories. Petroleum and industrial emissions were the largest anthropogenic sources of HCHO exposure in Southeast Texas, accounting for 44% of the total HCHO population exposure. Approximately 50% of the HCHO exposures associated with petroleum and industrial sources were directly emitted (primary), while the other 50% formed in the atmosphere (secondary) from precursor emissions of reactive compounds such as ethylene and propylene. Biogenic emissions also formed secondary HCHO that accounted for 11% of the total population-weighted exposure across the study domain. Off-road equipment contributed 3.7% to total population-weighted exposure in Houston, while natural gas combustion contributed 5% in Beaumont. Mobile sources accounted for 3.7% of the total HCHO population exposure, with less than 10% secondary contribution. Exposure disparity patterns changed with the location. Hispanic and Latino residents were exposed to HCHO concentrations +1.75% above average in Houston due to petroleum and industrial sources and natural gas sources. Black and African American residents in Beaumont were exposed to HCHO concentrations +7% above average due to petroleum and industrial sources, off-road equipment, and food cooking. Asian residents in Beaumont were exposed to HCHO concentrations that were +2.5% above average due to HCHO associated with petroleum and industrial sources, off-road vehicles, and food cooking. White residents were exposed to below average HCHO concentrations in all domains because their homes were located further from primary HCHO emission sources. Given the unique features of the exposure disparities in each region, tailored solutions should be developed by local stakeholders. Potential options to consider in the development of those solutions include modifying processes to reduce emissions, installing control equipment to capture emissions, or increasing the distance between industrial sources and residential neighborhoods.

Cleaning up while Changing Gears: The Role of Battery Design, Fossil Fuel Power Plants, and Vehicle Policy for Reducing Emissions in the Transition to Electric Vehicles.

Plug-in electric vehicles (PEVs) can reduce air emissions when charged with clean power, but prior work estimated that in 2010, PEVs produced 2 to 3 times the consequential air emission externalities of gasoline vehicles in PJM (the largest US regional transmission operator, serving 65 million people) due largely to increased generation from coal-fired power plants to charge the vehicles. We investigate how this situation has changed since 2010, where we are now, and what the largest levers are for reducing PEV consequential life cycle emission externalities in the near future. We estimate that PEV emission externalities have dropped by 17% to 18% in PJM as natural gas replaced coal, but they will remain comparable to gasoline vehicle externalities in base case trajectories through at least 2035. Increased wind and solar power capacity is critical to achieving deep decarbonization in the long run, but through 2035 we estimate that it will primarily shift which fossil generators operate on the margin at times when PEVs charge and can even increase consequential PEV charging emissions in the near term. We find that the largest levers for reducing PEV emissions over the next decade are (1) shifting away from nickel-based batteries to lithium iron phosphate, (2) reducing emissions from fossil generators, and (3) revising vehicle fleet emission standards. While our numerical estimates are regionally specific, key findings apply to most power systems today, in which renewable generators typically produce as much output as possible, regardless of the load, while dispatchable fossil fuel generators respond to the changes in load.

Feasibility study and techno-economic assessment of power-to-gas (P2G) technology based on solid oxide electrolysis (SOE).

Power-to-Gas (P2G) is considered as a promising energy storage technology in a long-time horizon. The rapid growth in the share of intermittent renewables in the energy mix is driving forward research and development in large-scale energy storage. This paper presents a feasibility analysis of a power-to-gas system in terms of various operating points and capacities. The analysis was performed using a system model, which features a solid oxide electrolyzer (SOE), a CO2 separation unit, and a methanation reactor as the key components. For the purposes of the techno-economic assessment (TEA) of the system, the CAPEX/OPEX estimation was performed and the cost structure defined. The model proposed in the study enables system-level optimization, including technical and economic criteria, considering two nominal scales: 10 kW and 40 GW, which corresponds to the nominal capacity of SOE in each case. According to the study, in an SOE-based P2G system, the cost of synthetic natural gas (SNG) production will fall by 15-21% by 2030 and 29-37% by 2050. SNG production would cost 3.15-3.75 EUR2023/kgSNG in 2030 and 2.6-3.0 EUR2023/kgSNG in 2050 for systems with SOE power >10 MW. Generally, product cost reductions occur as a result of material development and large-scale production, which influences the system's CAPEX. According to the research, the technology will break even by 2050. The large-scale power-to-gas system with a total of 40 GW installed capacity delivers a product price of 2.4 EUR2023/kgSNG with the average conversion efficiency of 68%.

Methods for Spatial Extrapolation of Methane Measurements in Constructing Regional Estimates from Sample Populations.

Methane emission estimates for oil and gas facilities are typically based on estimates at a subpopulation of facilities, and these emission estimates are then extrapolated to a larger region or basin. Basin-level emission estimates are then frequently compared with basin-level observations. Methane emissions from oil and gas systems are inherently variable and intermittent, which make it difficult to determine whether a sample population is sufficiently large to be representative of a larger region. This work develops a framework for extrapolation of emission estimates using the case study of an operator in the Green River Basin. This work also identifies a new metric, the capture ratio, which quantifies the extent to which sources are represented in the sample population, based on the skewness of emissions for each source. There is a strong correlation between the capture ratio and extrapolation error, which suggests that understanding source-level emissions distributions can mitigate error when sample populations are selected and extrapolating measurements. The framework and results from this work can inform the selection and extrapolation of site measurements when developing methane emission inventories and establishing uncertainty bounds to assess whether inventory estimates are consistent with independent large spatial-scale observations.

Stationarity and cycles in the energy consumption in the United States.

The purpose of this paper is twofold: analyzing stationarity of energy consumption by source in the United States and studying their cycles and pairwise synchronization. We study a panel of nine time series of monthly energy consumption for the period 1973-2022. Four of the series (namely coal, natural gas, petroleum, and nuclear electric power consumption) are non-renewables, whereas the remaining ones (hydroelectric power, geothermal, biomass, solar, and wind energy consumption) are renewable energy sources. We employ a nonparametric, panel stationarity testing approach. The results indicate that most of the series may be trend-stationarity, with nuclear and geothermal energy consumption being the only exceptions. Additionally, a study on potential cycles in the series of energy consumption by source is carried out, and subsequently we analyze pairwise concordance between states of different energy sources and between states of energy sources and the business cycle. Significant correlations are detected in the latter analysis, which are positive in the case of fossil fuel sources and negative for two renewable sources, namely geothermal and biomass energy consumption.

A comprehensive study on applications of nanomaterials in petroleum upstream and downstream industry.

Nanotechnology has emerged as a revolutionary technology that has been applied in the oil and gas industry for over a decade, spanning the upstream, midstream, and downstream sectors. Nanotechnology has made significant contributions to the exploration of crude oil and natural gas, both in underground and deep-water environments. It has also played a crucial role in improving the drilling process, enabling the extraction of oil and gas resources from beneath the Earth's surface. Nanoparticles, with their unique physical and chemical properties, such as high specific surface area, high pore volume, and small size, have demonstrated considerable potential in the oil industry. Extensive research has been conducted to explore various types of nanoparticles for advanced applications, including oil exploration, drilling, production, and enhanced oil recovery (EOR). Moreover, nanomaterials have found applications in downstream and intermediate sectors, such as crude oil refining, natural gas processing, and transportation and storage of petroleum products. Ongoing advancements in nanomaterial synthesis methods, the exploration of new nanomaterial uses, and understanding the remarkable properties of nanomaterials will continue to make them increasingly valuable in the oil and gas sector. The oil and gas industry recognises the potential of nanotechnology and nanoparticles and is investing significantly in research and development in this area. This comprehensive review aims to summarise successful applications of nanotechnology while addressing associated challenges. It serves as a valuable resource for future research and application endeavours in the field, highlighting the potential of nanotechnology in the oil and gas industry.

Sustainable planning: the case study of the Strait of Messina ports.

The energy and environmental policy carried out by the Port System Authority of the Strait (AdSP), in charge of the management of the ports spread along the Strait of Messina, is reported. The Environmental and Energy Planning Document of Port Systems (DEASP, the Italian acronym) is the document explaining the AdSP sustainable strategy to reduce GHG emissions. It defines specific measures, in order to improve energy efficiency in buildings and infrastructures, promote the use of renewable energy in the port area, and confer environmental benefits for the citizens of neighboring territories and port users. The main actions developed are as follows: photovoltaic solar plants and tidal energy systems, electrification of the docks to allow the shore supply of ships, and the construction of a Liquefied Natural Gas (LNG) storage plant to replace more polluting marine fuels, together with awareness campaigns on "green" issues, involving the 3 million users of these ports. Starting from the socio-economic and environmental analysis of the territorial context managed by AdSP, the DEASP analyses all the activities carried out inside port areas and reports the energy consumptions of the concessionaries, in the way to calculate the carbon footprint and develop an environmental sustainable strategy to reduce pollutant emissions. The interventions foreseen are assessed through the cost-benefit analysis and allow reducing the GHG emissions in 2030 up to 46%.